Tôle GI a. Propriétés physiques : 1. Épaisseur : (0,38~0,45) mm 2. Poids du rouleau : ≤ 5000 kg 3. Largeur du rouleau : 900-915 mm (la tôle GI doit être fournie en rouleau) 4. Épaisseur du revêtement de zinc ≥ 0,015 mm (de chaque côté de la tôle GI) 5. Poids du revêtement de zinc ≥ 0,0225 g par cm² 6. Poids : Poids unitaire de la tôle en fonction de la taille et du revêtement 7. La surface de la tôle/du rouleau est lisse, propre et exempte de toutes taches et doit avoir une couche galvanisée spéciale en damier d'acier doux cristallisé b. Composition chimique et propriétés mécaniques : 1.Carbone : 0,15 % maximum 2.UTS : 27~52 kg/mm2 3.Allongement : ≥ 18 % 4.Test de pliage avec norme : ≥ 6 fois de pliage à un angle de 90 degrés. 5.Test de pelage : pas de pelage lors de pliages répétés à 180 degrés
We would like to purchase the GI sheet from your company and resale it to the client. Here we enclose the details required by the clients below. Physical properties: 1. Thickness: (0.38~0.45) mm 2. Weight of roll: ≤ 5000 kg 3. Width of roll: 900-915 mm (GI Sheet must be supplied as roll) 4. Thickness of Zinc coating ≥ 0.015 mm (each side of GI Sheet) 5. Weight of Zinc coating ≥ 0.0225 gm per sq cm 6. Weight:Sheet unit weight according to size and coating 7. The surface of the sheet/roll is smooth, clean and free from all spotsand should have crystallized mild steel-checkered special galvanized layer.
are you manufacturer of GI Sheet we needed 200 tons of GI Sheet
Looking for GI Sheet wholesale
if you have this in your stock or you if you can make this custom GI sheet, please let us know 1. GI Sheet : a. Physical properties: 1. Thickness: (0.38~0.45) mm 2. Weight of roll: ≤ 5000 kg 3. Width of roll: 900-915 mm (GI Sheet must be supplied as roll) 4. Thickness of Zinc coating ≥ 0.015 mm (each side of GI Sheet) 5. Weight of Zinc coating ≥ 0.0225 gm per sq cm 6. Weight:Sheet unit weight according to size and coating 7. The surface of the sheet/roll is smooth, clean and free from all spotsand should have crystallized mild steel- checkered special galvanized layer b. Chemical composition & Mechanical properties: 1. Carbon: 0.15 % Maximum 2. UTS :27~52 kg/mm2 3. Elongation: ≥ 18% 4. Bending Test with standard: ≥ 6 times bending at 90 degree angle. 5. Peeling Test: No peeling at repeated 180 degree bending c. Packing: 1. The G I Sheet should be packed in roll will be wrapped with moisture/water proof paper on the top of the roll to protect moisture/water. After wrapping the roll should be covered with an extra G I Sheet and reinforced in three places with wrap (Two in two end & in middle). The inner & outer edges of the roll should be covered with angular sheet so that the edges of the rolled sheet should not affect for reinforcement. Than the roll to be fastened in lengthwise in four or more places as a required to avoid the looseness of roll. 2. The first sheet of each roll to be labeled with the following marking: (a) Name of manufacturer (b) brand Name (c) group No. (d) dimension and weight of each bundle (e) signature of the technical control department. 3. Galvanized roll can not be transported in any dirty carriages which carries NaCl, Ca(OH)2 and NH4CI. 4. Galvanized roll for delivery should be painted with neutralized mineral oil. 5. A certification is to be provided along with the delivery of each lot showing -name of manufacturer, weight, group No., dimension, results of tests and code No. of this standard. 6. Warrantee for 01 year after acceptance of the stores. d. 1. Country of origin: Group A Country 2. Country of manufacture: Country of Origin 3. Port of Shipment: Country of Origin. Kg 200000 2. GI Wire : Size: Dia 4.00±0.12 mm Technical Requirement: 1. Tensile Strength = 30-50 kg/mm2 2. Elongation= More than 10% 3. Carbon = 0.15-0.25% 4. Wt of Zinc Coating = More than 95 gm/M2 5. There should not have any ungalvanized spot on the surface of the wire. 6. The wire should pass the torsion test Kg 2000
Looking for Hr cold rolls gi sheet & coils
Want to Buy GI Sheet. Quantity 150MT
We need GI Sheet . Can you please quote us your C&F price to Bangladesh please?
